Ventilation System Performance: Beyond Rated Airflow

A ventilation unit can meet its published airflow and heat-recovery figures while an occupied bedroom still receives too little outdoor air. It can run quietly at one test point and sound intrusive at the speed needed after installation. A single favourable CO₂ reading cannot settle these questions.
For an overseas distributor or HVAC contractor, the useful distinction is between what has been tested on the equipment and what can be checked in the installed system. A credible project handover carries both.
A recent Eurovent Certita Certification article describes an approach to assessing complete residential ventilation systems. Its IAQVS programme considers the ventilation components together and simulates different dwellings, climates and occupancy conditions, evaluating several indoor-air-quality indicators alongside energy performance. The lesson for a project is to ask how the system performs under its intended conditions of use, instead of reading one equipment number as an overall IAQ score.
Start with the Equipment Data and Its Test Conditions
An ERV or HRV specification is the starting point. Buyers need to know the airflow available at the relevant external static pressure, fan power, heat-recovery data, filter specification, sound-test conditions and supported control functions.
Each figure comes with conditions attached. Maximum airflow may not be the flow the unit delivers through the planned ducts and terminals. A published recovery value applies to stated test conditions. A controller that displays CO₂ or relative humidity does not necessarily change ventilation in response to those readings.
Ask for curves or test points where the supplier has them, and identify the operating mode behind each value. Comparisons between products become more useful, and the installer has something concrete to check once the unit is connected to the building.
Then Check What Reaches the Rooms
Total supply airflow from a central unit does not show how that air is distributed. The installed ducts, branch settings, terminals and transfer paths determine what reaches each room. Occupancy and operating schedules decide which settings matter most.
A bedroom at night, with its door closed and the unit in quiet mode, is a different case from a daytime test at full speed. Record the airflow at that setting, not only at maximum. Our bedroom ventilation guide explains why a satisfactory whole-house total can still miss an occupied room.
The same principle applies to extract rooms. Check whether the intended supply and extract paths work with doors in their normal positions and with the system in its normal, boost and night modes, where those modes are specified.
Use IAQ Trends for the Questions They Can Answer
CO₂ trends can help investigate ventilation relative to occupancy. Log the reading with the number of occupants, door and window positions, sensor location and operating mode. A snapshot taken in an empty room says little about an occupied evening.
Relative humidity also needs context. Cooking, showering, laundry, outdoor weather and indoor temperature can all change the reading. Watch whether the system responds as designed, and whether other equipment handles active dehumidification. An ERV's moisture-transfer function is not a guarantee of humidity control.
Formaldehyde is a different pollutant. A CO₂ sensor cannot measure it, and a particle sensor cannot establish its concentration. Where materials or furnishings make it a project concern, assess the sources and use a measurement method suited to that pollutant. Outdoor particles and the condition of installed filters need their own checks. No single sensor reading covers indoor air quality.
A Two-Column Handover Check for Distributors
The table below separates information supplied for the equipment from evidence collected for the installed system. It is a project checklist, not an IAQVS certification method.
| Equipment test data and documentation | Installed-system checks |
|---|---|
| Airflow data at stated external static pressure and fan setting | Measured supply and extract airflow at relevant terminals, including normal and night settings |
| Fan power at documented operating points | Power draw and operating schedule at the settings actually commissioned, where measured |
| Heat-recovery data with its test conditions | Confirmed recovery, bypass and frost-protection control sequence, if fitted |
| Filter specification and associated pressure conditions | Correct filter fitted and accessible for service, with maintenance information handed over |
| Sensor and controller capabilities for the exact configuration | Sensor location, recorded CO₂ and RH trends, and observed control response under stated conditions |
| Published sound data with measurement conditions | Occupied-room sound assessment at the operating speed needed to deliver design airflow |
| Unit model, configuration and installation requirements | Final settings, airflow-balancing record, photographs, user instructions and service contacts |
The two columns are related, but the entries are not interchangeable. A room CO₂ log does not prove a unit's laboratory airflow rating. A unit's test certificate does not prove that every bedroom receives its design flow. Keeping both sets of evidence makes the handover more useful to the buyer, installer and after-sales team.
Where Energy Fits into the Assessment
Ventilation needs electricity to move air, and outdoor-air exchange affects heating or cooling demand. Cutting airflow solely to obtain a lower fan-power figure may also reduce the outdoor air reaching occupied spaces.
The IAQVS programme evaluates indoor air quality and energy together through defined simulations. A project commissioning record is more limited: it documents fan settings, measured power where available, schedules, and whether heat recovery and bypass operate as specified. A short site inspection or an energy bill does not establish certified annual IAQ or energy performance.
For buyers comparing two proposals, request the same design occupancy, room airflows and operating schedule for both. A lower energy figure may only describe a lighter ventilation duty.
What Should MENRED Project Buyers Request?
For a residential ERV or HRV project, share the dwelling type, location, floor plan, room occupancy, planned duct layout and desired operating modes. Ask the supplier for equipment data at the relevant operating point. Ask the installer for a room-by-room commissioning record and a plain explanation of what the sensors and controls do.
MENRED offers residential ERV and HRV options for different layouts. Product selection should be followed by system design and site verification. The questions above borrow the principle of whole-system assessment; they do not imply that a MENRED product or project holds IAQVS certification.
Frequently Asked Questions
Is rated airflow enough to assess a residential ventilation system?
No. Rated airflow describes the unit under stated conditions. The installed system also needs enough airflow at the relevant rooms and operating settings, with suitable supply, extract and transfer paths.
Does a low CO₂ reading prove good indoor air quality?
No. CO₂ helps assess occupant-related ventilation, particularly as a trend over time. It does not measure formaldehyde, particles or other indoor pollutants.
Can an ERV maintain a target relative humidity by itself?
That depends on climate, moisture sources, unit design and controls. Energy or moisture recovery is not active dehumidification. Check which device removes excess moisture and how the system responds when RH changes.
Is a commissioning checklist the same as IAQVS certification?
No. IAQVS follows a defined certification methodology for specified residential ventilation systems. A site checklist records project-specific installation and operating evidence. It cannot confer a certification grade.
Make the Handover Useful After Installation
If you are evaluating ventilation products for a residential project or distribution programme, send MENRED the floor plan, occupancy, target room airflows and expected operating modes. We can discuss suitable residential ventilation equipment and the product data your installer needs for a meaningful system handover.